Messages can be sent via mobile phones connected via USB, COM cable driver and the GSM modem (usually also connected via USB). It is easy, because many operators provide long-term SIM cards. Important: operators do not guarantee immediate delivery of SMS. In the case of critical notifications do not rely on SMS.

There is no guarantee that the commands above work on all the modems that need the HSO driver. Dokapon Kingdom Wii On Pc Iso Download. The tested device was a T-Mobile branded Globetrotter iCON 225 'web'n'walk Stick'.

That device was able to connect without problems after the method described. Some Globetrotter HSDPA cards, for example the iCON 225 (branded as Orange, T-Mobile web'n'walk stick, etc.

Have the serial modem interface disabled by default, and only offer an NDIS network interface for the data connection. If a dial command is issued, but no CONNECT response happens from the modem, it might be helpful to check this. To check on the setting, issue: [admin@MikroTik] >/system serial-terminal port=usb1 channel=0 [Ctrl-A is the prefix key] ATZ OK ATI0 Manufacturer: Option N.V. Model: GlobeTrotter HSDPA Modem Revision: 2.5.24Hd (Date: Apr 17 2009, Time: 08:59:36) OK AT_OIFC?

_OIFC: 2,1,1,0 OK AT_OIFC=? _OIFC: [2-3], [0,1], [1], [0-5] mdm, diag, app1, pcsc/gps MDM (0: N/A) (1: N/A) (2: ndis) (3: modem and ndis) DIAG (0: none) (1: enable) APP1 (0: none) (1: enable) PCSC/GPS (0: none) (1: pcsc enable) (2: GPS enable) (3: app2 enable) (4: GPS & PCSC) (5: GPS & app2) OK In this example, the MDM (modem) interface is set to 2, so no serial modem interface is enabled in the device. To change the setting, issue: AT_OIFC=3,1,1,0 You should get: OK To write the change permanently to the NVRAM of the device, issue: AT&W Unplug and re-plug the device, and issue: [admin@MikroTik] >/port print Flags: I - inactive # NAME CHANNELS USED-BY BAUD-RATE 0 usb1 4 9600 Number of channels should have increased. On the tested device, the last channel is the modem-interface (number 3 in RouterOS). According to the Linux HSO driver page at least five Option devices exist which do not have the modem interface enabled by default. Router Configuration for PPP Since RouterOS V4 (and latest versions 3) the PPP client configuration is made much easier compared to previous versions. Note: RouterOS does not support memory slot like SD for USB modems.

Use USB hub with USB modem and USB flash instead!' You do not get 'authenticated' and 'connected' There is something wrong with your settings.

Most likely, the ppp-client interface settings should be changed to match your provider's requirements. If the data-channel setting is wrong, there will be no connection. The number of available channels is shown under the /port list, port numbers start with 0.

Disable the interface and try another port number! Check if you can communicate with the modem by using the serial-terminal! Make sure the ppp-client is disabled! Turn off PIN request for your SIM card, it makes the life much easier. Do it in a phone if you do not know the correct AT command.

Speed of the link is not what expected It's possible that the modem has connected to GPRS network, not 3G. Use the 'scan' command for list of available networks: [admin@rb411u] /interface ppp-client>scan 0 Flags: C - current, A - available, F - forbidden OPERATOR CODE ACCESS-TECHNOLOGY SIGNAL-STRENGH C LV LMT GSM 24701 GSM compact -65 A LV LMT GSM 24701 3G F BITE LV 24705 3G F LV TELE2 24702 GSM compact F LV TELE2 24702 3G F BITE LV 24705 GSM compact -- [Q quit D dump C-z pause] Multiple inits (multiline inits) are required It is possible by dividing them using; character. Example: modem-init='AT+CGDCONT=5, 'IP ', 'internet.lmt.l ';AT+CGDCONT=6, 'IP ', 'internet.lmt.lv ';AT' Modem is not recognized after reboot (port becomes invalit) It is recomended to disable built-inf flash/cd drive. Here are some command for few modem brands: • ZTE modems: Disable: AT+ZCDRUN=8 Enable: AT+ZCDRUN=9 • HUAWEI modems: AT^U2DIAG=256 Huawei E3131 modem do not work with PPP interface The Huawei modem might be in the HiLink mode and in order to work with the PPP the switch is needed. Go to this page where you have instructions how to do that: Sms sending is not working • check port • check PIN • enable debug logging GSM, DEBUG • check log • create supout Sms receiving is not working • check port • check PIN • got delivery accounting sms? • allowed-number is correct with country code prefix +XXX? • secret matches?

• check sms store directly /sys serial usbX by issuing command at+cmgl=1 (lists all messages in message store) • enable debug logging GSM, DEBUG • check log • create supout PPP client is not working • check port • check PIN • dial-on-demand is set to no? • apn correct? • needs special modem-init (to handle PIN use at+cpin=XXXX)? • enable debug logging with topics ASYNC, DEBUG • check log • create supout PPP info is not working • check port • uses same channel info-channel == data-channel (can't work while ppp-client is enabled)?

GSM device configuration GSM device configuration nVision enables an admin alert notification to be defined by means of SMS messages. Sending notifications via SMS is a convenient way of informing in case of occurrence of predefined, such as significant change in the website content (attack suspected), files copied to the mobile device, or hardware resources changed. Erco Light Studio Software.

Messages can be sent via mobile phones connected via USB, COM cable driver and the GSM modem (usually also connected via USB). It is easy, because many operators provide long-term SIM cards.

Important: operators do not guarantee immediate delivery of SMS. In the case of critical notifications do not rely on SMS text messages or e-mails. Tested devices The following common telephones and modems were tested for cooperation with the software.