Mar 16, 2017. Troubleshooting problems with your vacuum sealer. Tips and tricks on how to fix your FoodSaver vacuum sealer. View and Download FoodSaver V1085 quick start manual online. FoodSaver FoodSaver Appliance Quick Start. V1085 Food Saver pdf manual download.

I have a Food Saver brand Vacuum Sealer, that all of a sudden stopped working properly. It has no On-Off switch. You simply plug it in, and then put the bag up to the vacuum area and then press down and hold the lid when its vacuuming the air out and then seals the bag closed. When it stopped working, a vacuum bag was placed (as we normally would) and then the lid was put down and pressed. The motor is still running, but normally it makes a louder noise as its vacuuming the air out, and this time it didn't work. Since it wouldn't vacuum the air, it then wouldn't also seal the bag.

I checked the single air hole on the unit, and there isn't anything obstructing the flow of air, and the bag was put properly in the machine. I also tried using a new bag (just in case the other one was defective) but it made no difference. All the bags come off a large roll. You seal one end, fill it, and then vacuum the air and finally it seals. I've been using this machine for several years with no issues, and this isn't a new roll of bags.

Any ideas on what to do to service it and hopefully get it working again? I also want to thank the folks on this thread (even though it's older) for their various advice and expertise. I picked up a FoodSaver at a thrift store - motor and vacuum worked, it just wouldn't seal. Thanks to the advice in this thread, I also narrowed down the problem to the pressure sensor switch. Had to un-solder it, and then open up the hex screw, but after cleaning the switch (q-tips & rubbing alcohol) my unit is working. I would add that I wasn't super careful in noticing how far the hex screw was adjusted, so it took a couple tries to get it adjusted back to the right pressure.

If you haven't already done so, I would suggest doing a thorough inspection of the sealing system. Using a good magnifying glass, check the wire under the Teflon sealing strip for any obvious breaks or discoloration (such as a burn mark). If that appears fine, open up the unit.

You should see that the sealing strip wire is held under tension with small coil springs on either end. Check that there is still tension on both ends. If not, it would indicate that there is a break along the wire and it would need to be replaced. If you have access to a multimeter, you could also use that to check for any breaks in the sealing strip.

If the sealing strip is okay, I would check the wiring from the sealing strip to the switch (that controls the vacuum and sealing operations). My unit makes a pretty obvious 'click' noise when the bag is vacuumed and it begins the sealing; but if you're not hearing that, it could mean a problem at the switch.

Beyond that, check all the connectors to the motor and the circuit board for any obvious problems. Let me know how it works out. I just broke mine out after about 2 years, and it seemed to evacuate the bag ok, but not quite enough to have it seal the bag. I had stored it for so long, the foam rubber gasket was a little compressed so wasn't working as well as it should. I left it out (open) all night and it works fine again this morning. I think when I store it from now on, I'll put something in there so it won't close all the way and compress the gaskets.

Nice that I didn't have to crack it open. Since I was on this page, I was obviously ready. If you look closely in the pic with the motor (pump) & the green circuit board, there is a block. Easy fix, go to a pet store & get 'fish pump air line', & replace that section, less than $1.

Check the red barrel connected to the brown side of the circuit board. This a sensor to vary the 'pressure limit' before the sealing process is triggered. List Of Alloys And Their Composition And Uses Pdf File here. If anything is sucked into it, the sensor will not work. If you like small items, You can take it apart & clean it. Unscrew the hexagon screw. A small flat bladed screw driver, fits quite well. (& count turns until unscrewed, so you can put it back; exactly the way it was).

Carefully remove the spring hidden inside. Inside is a metal plate mounted on a piece of rubber; (non-removable). Use a Q-tip & alcohol to clean the metal plate, let dry.

Re-install spring & screw back in the hexagon screw; exactly the way it was. I just want to thank you, tvandyke.

Your instructions to canucksgirl on the pressure switch and how to clean it saved my Foodsaver v345 from certain demise. The pump was working great, but the unit wouldn't seal. After some Googling, I found this post and did what you said. Foodsaver is back in action.

The one thing you didn't mention but that I figured out from another website is you need to desolder the pressure valve off the circuit board to successfully remove the hex screw. But I needed an excuse to buy a soldering station (my first) and learn how to solder. Now what to do with it? Time to build a drone!!:).

Read the FoodSaver V1085 manual - avoid problems An important point after buying a device FoodSaver V1085 (or even before the purchase) is to read its user manual. We should do this for several simple reasons: • to know how to properly use the device • to know how to perform maintenance/ periodic checks of correct operation of the product FoodSaver V1085 • to know what to do in case of failure FoodSaver V1085 If you have not bought FoodSaver V1085 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data FoodSaver V1085 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, FoodSaver V1085 you will learn all the available features of the product, as well as information on its operation.

The information that you get FoodSaver V1085 will certainly help you make a decision on the purchase. If you already are a holder of FoodSaver V1085, but have not read the manual yet, you should do it for the reasons described above. Dissertation Angela Merkel Pdf Download.

You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime FoodSaver V1085. However, one of the most important roles played by the user manual is to help in solving problems with FoodSaver V1085. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device FoodSaver V1085 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center.